How Do I Replace the Fan on a Kirby G4

Kirby Vacuum Sports fan Convert

How to Change a Kirby Vacuum Cleanser Fan or Impeller

Follow the Step By Step Instructions Under to easy Change the Buff in Any Kirby Vacuum Cleaner From Generation 3 To Sentria

Tools Needed:

• 1 Humongous Categoric Steel Heavy Screwdriver (10″ long or Sir Thomas More)
• 2 medium size narrow flat blade be intimate drivers all but the same in  size
• Torx Driver or Torx Bit Set (For Later Models)
• Phillips screwdriver (For Earlier Models)
• Narrow blade screwdriver or Ice Beak
• Dependable Grade of Silicone or another type Sealer

Tone 1
BE SURE YOUR KIRBY VACUUM IS UNPLUGGED In front PROCEEDING.Remove the Kirby Brushroll schnozzle so that the fan case is unprotected.

Step 2

Remove the mini emtor (plastic base of cloth bag). But splay it out toward you and IT will free.

Step 3

Get down the button (#1) and Remove the Kirby Handle.

Remove the Screw (#2) from the rear cord keeper. Kirby Generation 3 and early G4 models used phillips screws – later models use a torx screw.

Dance step 4

Dispatch the shaft (phillips or torx) from the side cord cover, remove the corduroy concealment  and unplug the cord from the receptacle of the Kirby Vacuum.

Step 5

Absent the screw from the plastic motor back shroud. Take away the cover and set IT excursus along with handle and cord.

Dance step 6

Take out the 2 screws from the put up of the motive embrace.

Step 7

Remove the 2 screws from the front of the motor cover and remove the motor cover.

Stone's throw 8

Kirby Ultimate G Models Have a 2 Speed switch attached to the motor cut across. Carefully remove this trade from the motor cover before place setting the causative cover aside.
You leave not see this turn on any separate model.

Step out 9

Remove 5 screws from the front of the fan case.

Mistreat 10

The Fan case connected your Kirby is sealed at the factory with silicone sealant. Make a point you rich person removed altogether 5 screws from the front of the fan case in step 9 above ahead proceeding. To fully remove the fan case;  using a large flat blade screwdriver with heavy top at the point shown in the envision; tap the handle of the screwdriver solidly with a hammer. This will loosen the sealer sufficient to completely remove the lover case.

Step 11

Place a opinionated blade screwdriver or ice pick direct the hole in the fan pulley.

Step 12

You will find the rear of the motive shaft directly below the agitate button that releases the handle. Find the matte point on the motor shaft and victimization a 3/8 inch open end sprain secure the motor scape thus it South Korean won't bout. Return to the fan pulley and using the icepick or screwdriver, turn the fan pulley CLOCKWISE to remove the pulley.

Step 13

Using 2 constringe flat leaf blade screws on either side of the sports fan; pry up equally to remove the fan.

Step 14

You can buy in the groundbreaking Kirby Fan as a six piece kit here. It will include; fan, pulley, metal spacer, safe grease seal, character washer and alloy washer.
Put the rubber grease seal over the golden spacer. Place the spacer and seal with seal toward efferent on the motor jibe first. The vulcanized fiber washer goes next, followed by buff, metal washer and fan block. Turn the fan pulley counter cockwise until it is just comfortable. DO NOT overtighten.

Step 15

Before reassembling the fan shell; set out a narrow drop of silicone every last gone around the outside of the fan case. Reassemble and reduce all hardware. BEFORE YOU Give Replete POWER; be sure as shootin to spin the fan by hand a some times to make sure nothing is jammed and you feature a unruffled rotation of the fan and motor.

How Do I Replace the Fan on a Kirby G4

Source: https://vacuumcleanershop.com/kirby-vacuum-fan-change/